Bespoke work away from masts and oars

With a proven pedigree in the world of wooden yacht masts and oars, our skills and knowledge have often been called upon within similar industries. As a glue-lam specialist and with the flexibility and facilities to take on a wide range of projects, diversification has become common place.

With the growing demand for traditional and sustainable materials within modern architecture, internal and external columns, both structural and cosmetic, have become regular work to satisfy this growing market. With the ability to turn almost any size of column from a variety of materials, there is little we cannot accommodate. 

The link below will highlight some of the bespoke projects we have undertaken over the years. 

The logical progression into wooden masts

Over the years Collars' spars have been used in Olympic competition, crossed all of the worlds Oceans, and can be found on nearly all wooden sparred production boats ever made. With a capacity of producing any wooden mast or spar up to 100' in length....


Having made our name in producing the finest quality wooden rowing oars for crews throughout the world, it is hardly surprising that we are still producing a comprehensive range today. At the lower end of the range are the standard wooden oars, offering quality and value for everyday use. Using the skills from three generations of the Collar family, a pair of Spruce spoon or skiff oars can be produced individually to the customer's requirements.


Whether looking to replace an historical flagpole, or raising a celebratory flag, our pedigree in producing the finest quality wooden masts for over 80 years makes Collars the obvious choice for making any flagpole. Using the finest quality timber available, our skilled craftsmen are able turn by hand, any size or configuration required. With our bespoke service, we will guide you throughout the complete process, from an initial consultation to erecting the finished product.


With a history dating back over 80 years, we have produced mast and spars for some of the most beautiful yachts in existence. Specialising in producing the finest quality yacht masts and spars, we pride ourselves on a personal, tailored service and maintain a close and constant contact with our customers. From the critical choice of timber to the final stages of smoothing and varnishing, a Collars product has over eighty years of experience and expertise put into it, making us the number one choice time and time again.

The following links are a small selection of the some of projects we have been proud to be part of in recent years.

Contact us

Glue - A bit about the Sticky Stuff


With the glue being a very important part of a mast or spar, we are asked on a regular basis 'what sort of glue do we use?'. So in an attempt to provide an answer an put some common myths to bed, this is where we stand:  

There are many glues around all with place in the market and using the best glue for the application is really the key. Think as though you would not try and stick a broken plate together with Pritt-stick; but it is very good when used on paper. The same goes for a small wooden dinghy mast, such as an Enterprise, that may only have 12mm walls as a gluing surface, bending and flexing all over the place, dunked in the water every so often, and used as the cover ridge pole throughout the winter; and not forgetting it needs to withstand at least 30 years of this type of abuse.

The answer in this case is the Urea-formaldehyde Aerolite 300 adhesive; and before anyone starts to point out the shortcomings with this glue, please remember it was developed to stick the Sitka Spruce parts in planes together, and a good glue joint is said to be 3 times stronger than the spruce itself. There is no pre-mixing, the glue is spread from the pot onto one surface, the acid hardener is spread onto the opposite surface, and the two are then simply pressed together. Great commercially as there is zero waste, and also with it being clear, the glue lines are completely invisible in most cases.  

While Aerolite is good on the small Sitka mast, it does not perform as well when it comes to Columbian Pine spars, so we switch to a resorcinol phenol formaldehyde resin. The 'traditional red boatbuilders glue' as it is sometimes referred to, but a true structural adhesive, and if some basic application 'rules' are followed, it's a hard one to beat. We use resorcinol for all Sitka spars over approximately 30', nearly all Pine spar produced, and with its ability to flex and move with the wood, combined with excellent UV stability; it is definitely a firm favourite.

Although you will find a small pot of Epoxy in our glue cupboard it is not something we use when it comes to gluing up masts. Some people will, but for us there are too many reasons why it does not match the properties of resorcinol - in our given application. Single part Polyurethanes likewise have been a great breakthrough when it comes to joinery work, but once again when you're dealing with a glue-lam construction one has to tread with caution. Similarly melamine glues are on par with resorcinol, but unfortunately out of reach when it comes to cost and availability. The glue market is constantly changing with what were at one time Aerospace glues now readily available in your local hardware shop, but the one thing we do have a tendency to do is stick with what we know and trust, as all our products rely upon it.